{"title":"Audi Coupe Quattro B2","description":null,"products":[{"product_id":"audi-sport-quattro-replica-wishbone-front-axis","title":"Audi Sport Quattro replica wishbone front axis","description":"Audi Sport Quattro S1 replica wishbones for front and rear axle. With high attention to detail, this is the \u003cstrong\u003ebest replica wishbones available\u003c\/strong\u003e.\u003cbr\u003e\n\u003cbr\u003e\nFor quattro cars that need unchanged geometry in every road, gravel and track conditions as stock wishbones pressed and steel tend to bend if used in harsh conditions. Wishbones enable wide camber wheel adjustment for track use. It gives up to 25 mm more camber adjustment.\u003cbr\u003e\n\u003cbr\u003e\nAdditionally Audi Sport replica wishbone moves the wheel to the front of the car giving more caster for better car handling. Aluminum pin is a perfect replica that contains all the elements of the original. They are suitable for rally stages and track use when standard wishbone gives up.\u003cbr\u003e\n\u003cbr\u003e\nThey provide greater strength that is required to withstand the much greater stresses and substantial geometry changes also become essential for effective use in your quattro. Tested on our race and rally cars.\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eWhat's Included:\u003c\/strong\u003e\u003cbr\u003e\n- two wishbones for front axle (please state uprights type B2 or divided B3\/B4 - see picture)\u003cbr\u003e\n- two aluminum ball joint carriers milled on CNC machine and anodized in \u003cstrong\u003eblack\u003c\/strong\u003e\u003cbr\u003e\n- two regreasable sport Fluro bearings (22 mm hole)\u003cbr\u003e\n- two steel pins to connect with OEM struts (front - please state 17mm, 18mm or 19 mm pin)\u003cbr\u003e\n- four steel galvanized locking plates for securing aluminum ball joint carriers\u003cbr\u003e\n- all necessary screws for mounting ball joint carriers and steel pins\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e\n- Can be used in conjunction with the standard front sub-frame\u003cbr\u003e\n- Made to work with OEM uprights\u003cbr\u003e\n- Allows for massive camber adjustment (up to 25mm more versus OEM) and wider track\u003cbr\u003e\n- Gives additional caster. Audi B2 OEM caster is 1,25 and with our wishbone it is 2.65\u003cbr\u003e\n- Works fine with Audi Sport blade type anti roll bars\u003cbr\u003e\n- Works with Audi Sport uprights (22 mm bolt)\u003cbr\u003e\n- Prepared to work with additional trailing arm (front)\u003cbr\u003e\n- Possible to use with \"turn stop\" on Audi Sport uprights\u003cbr\u003e\n- On the contact area between aluminum ball joint carrier and inside of the wishbone the area is knurled for better grip of the carrier\u003cbr\u003e\n- To be used with 37mm diameter bushes for mounting the wishbone to the subframe\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003e\u003cb\u003eFitment:\u003c\/b\u003e\u003c\/strong\u003e\u003cbr\u003e\n- Audi RS2\u003cbr\u003e\n- Audi B2 Coupe, Sedan\u003cbr\u003e\n- Audi B3\/B4, Coupe, Sedan, Avant\u003cbr\u003e\n\u003cbr\u003e\nBending machine ­used and milling machine for pipe treatment. Pipes are milled, metal plate is stamped, ends of the pipe are pressed and flattened for fastening of bushes, plug and bends are cut out on the laser, bushes are turned and grinded, rocker arm is welded in welding tool, dimensional tolerances: ­ 0,03 mm, concentricity tolerance 0,01 mm, tolerances are checked on separate measurement device.\u003cbr\u003e\n\u003cbr\u003e\nKnurling is made on the press by inserting the mass of material - 80 metric tons. MIG ­welding is used to connect all the pipes together to replicate Audi Sport manufacturing process. The wishbone is made of reinforced steel and powder painted in black color.\u003cbr\u003e\n\u003cbr\u003e\n\u003cem\u003eNotice: Front wishbones increase significantly caster angle. Important note -\u0026gt; ball joint housing used in this kit has brake disc clearance is reduced in relation to OEM discs. It is not possible to use this housing with brakes discs that reduce ET compared to OEM disc brakes for example Porsche 996 calipers with 330 rotors. \u003c\/em\u003e","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826673307997,"sku":"WAS-001","price":995.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/DSC_4663.jpg?v=1765197575"},{"product_id":"audi-b2b3b4-top-mount-pair","title":"Audi B2\/B3\/B4 top mount (pair)","description":"Two piece top mount direct replacement for OEM Audi rubber part. Includes Fluro precision 35mm race bearing secured with an steel locking ring. Bearing is maintenance free. Top mounts parts are produced with C.N.C. machinery.\u003cbr\u003e\n\u003cbr\u003e\nWhat's Included:\u003cbr\u003e\n- set of \u003cstrong\u003etwo\u003c\/strong\u003e aluminum top mounts for one axle\u003cbr\u003e\n- Fluro bearings \u0026amp; steel locking ring\u003cbr\u003e\n- six M6 alen head screws grade 8.8 for tightening upper and lower top mount section\u003cbr\u003e\n- sleeve nuts \u0026amp; step down spacer\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- \u003cstrong\u003ePrice for a pair\u003cbr\u003e\n- \u003cstrong\u003eWorks fine with stock suspension\u003c\/strong\u003e\u003c\/strong\u003e\u003cbr\u003e\n- Spherical bearing top mounts with zero play\u003cbr\u003e\n- Proven in race and rally cars\u003cbr\u003e\n- Tightened with six M6 screws\u003cbr\u003e\n- CNC milled from solid 7075 aluminum\u003cbr\u003e\n- Fits 14mm shock absorber end with M14x1.5 thread (fits original Audi shock absorber and many aftermarket solutions - Monroe, KW, Koni, Boge, Bilstein ect.)\u003cbr\u003e\n- Hard anodized to 35 microns in black color\u003cbr\u003e\n\u003cbr\u003e\nFitment:\u003cbr\u003e\nAudi B2 Coupe Quattro - front and rear (inc. UrQuattro)\u003cbr\u003e\nAudi B2 Coupe FWD - front\u003cbr\u003e\nAudi B2 Sedan Quattro - front and rear\u003cbr\u003e\nAudi B2 Sedan FWD - front\u003cbr\u003e\nAudi B3 Coupe Quattro - front and rear\u003cbr\u003e\nAudi B3 Coupe FWD - front\u003cbr\u003e\nAudi B3 Sedan Quattro - front and rear\u003cbr\u003e\nAudi B3 Sedan FWD - front\u003cbr\u003e\nAudi B4 Coupe Quattro - front and rear (inc. S2)\u003cbr\u003e\nAudi B4 Coupe FWD - front\u003cbr\u003e\nAudi B4 Sedan FWD \u0026amp; Quattro - front (inc. S2)\u003cbr\u003e\nAudi B4 Avant FWD \u0026amp; Quattro - front (inc. S2, RS2)\u003cbr\u003e\n\u003cbr\u003e\n\u003cem\u003eNotice: The top six M6 screws should be tightened using Locktite 243 at 10 Nm. The main screw should be tightened using Locktite 243 at 90 Nm. Please tighten the bolts when the car is standing on its wheels to precise apply the torque to the bolt. \u003c\/em\u003e","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826673766749,"sku":"TMA-002","price":170.5,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/TMA-002_1-audi-b2-b3-b4-top-mount.jpg?v=1765197576"},{"product_id":"audi-b2b3b4-top-mount-with-12mm-offset-pair","title":"Audi B2\/B3\/B4 top mount with 12mm offset (pair)","description":"Two piece top mount with 12 mm offset made from PA9 Aluminum produced on C.N.C. machinery. It is the biggest offset available on the market !\u003cbr\u003e\n\u003cbr\u003e\nCan be used to set maximum camber\/caster without cutting the cars body. Includes Fluro (German) precision 35mm race bearing secured with an steel locking ring. Bearing is maintenance free.\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eWhat's Included:\u003c\/strong\u003e\u003cbr\u003e\n- set of \u003cstrong\u003etwo\u003c\/strong\u003e aluminum top mounts for one axle\u003cbr\u003e\n- Fluro bearings \u0026amp; steel locking ring\u003cbr\u003e\n- six M6 alen head screws grade 8.8 for tightening upper and lower top mount section\u003cbr\u003e\n- sleeve nuts \u0026amp; step down spacer\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e\n- \u003cstrong\u003ePrice for a pair\u003c\/strong\u003e\u003cbr\u003e\n- \u003cstrong\u003eWorks fine with stock suspension\u003c\/strong\u003e\u003cbr\u003e\n- Fits 14mm shock absorber end with M14x1.5 thread (fits original Audi shock absorber and many aftermarket solutions - Monroe, KW, Koni, Boge, Bilstein ect.)\u003cbr\u003e\n- Spherical bearing top mounts with zero play\u003cbr\u003e\n- Proven in race and rally cars\u003cbr\u003e\n- Tightened with six M6 screws\u003cbr\u003e\n- CNC milled from solid 7075 aluminum\u003cbr\u003e\n- Caster\/camber 12mm offset adjustment\u003cbr\u003e\n- Max 11 degree tilt in front direction allowed to use offset subframe bushing for extra camber\u003cbr\u003e\n- Camber change from original 1.25 degree (Audi Ur-Quattro) up to 4.3 degree together with offset subframe bushing or 4.6 degree with our Audi Sport front wisbones replicas\u003cbr\u003e\n- Hard anodized to 35 microns in black color\u003cbr\u003e\n- Weight 1 kg (pair)\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e\u003cbr\u003e\nAudi B2 Coupe Quattro - front and rear (inc. UrQuattro)\u003cbr\u003e\nAudi B2 Coupe FWD - front\u003cbr\u003e\nAudi B2 Sedan Quattro - front and rear\u003cbr\u003e\nAudi B2 Sedan FWD - front\u003cbr\u003e\nAudi B3 Coupe Quattro - front and rear\u003cbr\u003e\nAudi B3 Coupe FWD - front\u003cbr\u003e\nAudi B3 Sedan Quattro - front and rear\u003cbr\u003e\nAudi B3 Sedan FWD - front\u003cbr\u003e\nAudi B4 Coupe Quattro - front and rear (inc. S2)\u003cbr\u003e\nAudi B4 Coupe FWD - front\u003cbr\u003e\nAudi B4 Sedan FWD \u0026amp; Quattro - front (inc. S2)\u003cbr\u003e\nAudi B4 Avant FWD \u0026amp; Quattro - front (inc. S2, RS2)\u003cbr\u003e\n\u003cbr\u003e\n\u003cem\u003eNotice: The top six M6 screws should be tightened using Locktite 243 at 10 Nm. The main screw should be tightened using Locktite 243 at 90 Nm. Please tighten the bolts when the car is standing on its wheels to precise apply the torque to the bolt. \u003c\/em\u003e","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826673799517,"sku":"TMA-001","price":235.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/audi-b2-b3-b4-top-mount-with-12mm-offset-s2-rs2-urquattro-coupe-quattro-tma-001-2.jpg?v=1765197579"},{"product_id":"audi-sport-replica-wishbone-full-set-for-b3b4-divided-type-uprights","title":"Audi Sport replica wishbone full set for B3\/B4 divided type uprights","description":"Audi Sport Quattro S1 replica wishbones \/ control arms for front and rear axle. With high attention to detail, this is the \u003cstrong\u003ebest and most precise replica wishbones available\u003c\/strong\u003e.\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eMade for Audi B3\/B4 divided uprights in B2 \/ B3 or B4 Coupe Quattro cars.\u003c\/strong\u003e\u003cbr\u003e\n\u003cbr\u003e\nFor quattro cars that need unchanged geometry in every road, gravel and track conditions as stock wishbones pressed and steel tend to bend if used in harsh conditions. Wishbones enable wide camber wheel adjustment for track use. It gives up to 25 mm more camber adjustment.\u003cbr\u003e\n\u003cbr\u003e\nAdditionally Audi Sport replica wishbones \/ control arms move the wheel to the front of the car giving more caster for better car handling. Aluminum pin is a perfect replica that contains all the elements of the original. They are suitable for rally stages and track use when standard wishbone gives up.\u003cbr\u003e\n\u003cbr\u003e\nThey provide greater strength that is required to withstand the much greater stresses and substantial geometry changes also become essential for effective use in your quattro. Tested on our race and rally cars.\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eWhat's Included:\u003c\/strong\u003e\u003cbr\u003e\n- two wishbones [ control arms ] (E355 N \/ St 52.4 steel) for front axle\u003cbr\u003e\n- two wishbones [ control arms ] (E355 N \/ St 52.4 steel) for rear axle\u003cbr\u003e\n- four aluminum (PA9 \/ 7075) ball joint carriers milled on CNC machine and anodized in silver\u003cbr\u003e\n- four maintenance free sport Fluro bearings (22 mm hole)\u003cbr\u003e\n- four steel pins (EN C45) to connect with OEM struts (front and rear - B3\/B4 divided type uprights)\u003cbr\u003e\n- eight steel galvanized locking plates for securing aluminum ball joint carriers\u003cbr\u003e\n- all necessary screws for mounting ball joint carriers and steel pins\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e\n\u003cstrong\u003e- Can be used in conjunction with the standard front\/rear sub-frame\u003c\/strong\u003e\u003cbr\u003e\n\u003cstrong\u003e - Made to work with OEM uprights (quattro)\u003c\/strong\u003e\u003cbr\u003e\n- Allows for massive camber adjustment (up to 25mm more versus OEM) and wider track\u003cbr\u003e\n- Gives additional caster. Audi B4 OEM caster is 2 and with our wishbone it is 2.65\u003cbr\u003e\n- Works fine with Audi Sport blade type anti roll bars\u003cbr\u003e\n- Works with Audi Sport uprights (22 mm bolt)\u003cbr\u003e\n- Prepared to work with additional trailing arm (both in front and rear)\u003cbr\u003e\n- Possible to use with \"turn stop\" on Audi Sport uprights\u003cbr\u003e\n- On the contact area between aluminum ball joint carrier and inside of the wishbone the area is knurled for better grip of the carrier\u003cbr\u003e\n- To be used with 37mm diameter bushes for mounting the wishbone to the subframe\u003cbr\u003e\n\u003cbr\u003e\nBending machine ­used and milling machine for pipe treatment. Pipes are milled, metal plate is stamped, ends of the pipe are pressed and flattened for fastening of bushes, plug and bends are cut out on the laser, bushes are turned and grinded, rocker arm is welded in welding tool, dimensional tolerances: ­ 0,03 mm, concentricity tolerance 0,01 mm, tolerances are checked on separate measurement device.\u003cbr\u003e\n\u003cbr\u003e\nKnurling is made on the press by inserting the mass of material - 80 metric tons. MIG ­welding is used to connect all the pipes together to replicate Audi Sport manufacturing process. The wishbone is made of reinforced steel (E355 N \/ St 52.4) and powder painted in black color.\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e\u003cbr\u003e\n- All Audi Coupe Quattro cars with divided uprights. See picture in the gallery.\u003cbr\u003e\n- Audi S2 Coupe\u003cbr\u003e\n- Audi 80 Coupe Quattro\u003cbr\u003e\n- Audi 90 Coupe Quattro\u003cbr\u003e\nIf you have doubts if they will fit. Write us a message and we will be glad to help you with the right setup.\u003cbr\u003e\n\u003cbr\u003e\n\u003cem\u003eNotice: Instructions are provided to the customer on the installation of the kit. Front wishbones increase significantly caster angle.  Important note -\u0026gt; ball joint housing used in this kit has brake disc clearance is reduced in relation to OEM discs. It is not possible to use this housing with brakes discs that reduce ET compared to OEM disc brakes for example Porsche 996 calipers with 330 rotors.\u003cbr\u003e\n\u003c\/em\u003e","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826674389341,"sku":"WAS-003","price":1695.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/WAS-003-1-tubular-audisport-wishbone-set-quattro-s1-sport-audisport.jpg?v=1765197582"},{"product_id":"audi-sport-quatro-s1-replica-wishbones-full-set-for-b2-type-uprights","title":"Audi Sport quatro S1 replica wishbones full set for B2 type uprights","description":"Audi Sport Quattro S1 replica wishbones \/ control arms for front and rear axle. With high attention to detail, this is the \u003cstrong\u003ebest and most precise replica wishbones available\u003c\/strong\u003e.\u003cbr\u003e\n\u003cbr\u003e\nFor quattro cars that need unchanged geometry in every road, gravel and track conditions as stock wishbones pressed and steel tend to bend if used in harsh conditions. Wishbones enable wide camber wheel adjustment for track use. It gives up to 25 mm more camber adjustment.\u003cbr\u003e\n\u003cbr\u003e\nAdditionally Audi Sport replica wishbones \/ control arms move the wheel to the front of the car giving more caster for better car handling. Aluminum pin is a perfect replica that contains all the elements of the original. They are suitable for rally stages and track use when standard wishbone gives up.\u003cbr\u003e\n\u003cbr\u003e\nThey provide greater strength that is required to withstand the much greater stresses and substantial geometry changes also become essential for effective use in your quattro. Tested on our race and rally cars.\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eWhat's Included:\u003c\/strong\u003e\u003cbr\u003e\n- two wishbones [ control arms ] (E355 N \/ St 52.4 steel) for front axle\u003cbr\u003e\n- two wishbones [ control arms ] (E355 N \/ St 52.4 steel) for rear axle\u003cbr\u003e\n- four aluminum (PA9 \/ 7075) ball joint carriers milled on CNC machine and anodized in silver\u003cbr\u003e\n- four maintenance free sport Fluro bearings (22 mm hole)\u003cbr\u003e\n- two steel pins (EU C45) to connect with OEM struts (for Audi Coupe Quattro 17 mm, for Ur-quattro 18mm)\u003cbr\u003e\n- two steel mounts (EU C45) for rear OEM struts\u003cbr\u003e\n- eight steel galvanized locking plates for securing aluminum ball joint carriers\u003cbr\u003e\n- all necessary screws for mounting ball joint carriers and steel pins\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e\n- Can be used in conjunction with the standard front\/rear sub-frame\u003cbr\u003e\n- Made to work with OEM uprights (Quattro B2\/B3, Ur-quattro - see drawing)\u003cbr\u003e\n- Allows for massive camber adjustment (up to 25mm more versus OEM) and wider track\u003cbr\u003e\n- Gives additional caster. Audi B2 OEM caster is 1,25 and with our wishbone it is 2.65\u003cbr\u003e\n- Works fine with Audi Sport blade type anti roll bars\u003cbr\u003e\n- Works with Audi Sport uprights (22 mm bolt)\u003cbr\u003e\n- Prepared to work with additional trailing arm (both in front and rear)\u003cbr\u003e\n- Possible to use with \"turn stop\" on Audi Sport uprights\u003cbr\u003e\n- On the contact area between aluminum ball joint carrier and inside of the wishbone the area is knurled for better grip of the carrier\u003cbr\u003e\n- To be used with 37mm diameter bushes for mounting the wishbone to the subframe\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e\u003cbr\u003e\n- Audi Coupe Quattro\u003cbr\u003e\n- Audi Ur-quattro\u003cbr\u003e\n\u003cbr\u003e\nBending machine ­used and milling machine for pipe treatment. Pipes are milled, metal plate is stamped, ends of the pipe are pressed and flattened for fastening of bushes, plug and bends are cut out on the laser, bushes are turned and grinded, rocker arm is welded in welding tool, dimensional tolerances: ­ 0,03 mm, concentricity tolerance 0,01 mm, tolerances are checked on separate measurement device.\u003cbr\u003e\n\u003cbr\u003e\nKnurling is made on the press by inserting the mass of material - 80 metric tons. MIG ­welding is used to connect all the pipes together to replicate Audi Sport manufacturing process. The wishbone is made of reinforced steel and powder painted in black color.\u003cbr\u003e\n\u003cbr\u003e\n\u003cem\u003eNotice: minor tools are required to install rear wishbones bolts. You need to have burner to heat the rear uprights for the bolt to be pushed inside. Instructions are provided to the customer on the installation of the kit. Front wishbones increase significantly caster angle. Important note -\u0026gt; ball joint housing used in this kit has brake disc clearance is reduced in relation to OEM discs. It is not possible to use this housing with brakes discs that reduce ET compared to OEM disc brakes for example Porsche 996 calipers with 330 rotors. \u003c\/em\u003e","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826674422109,"sku":"WAS-002","price":1695.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/WAS-002_1-tubular-audisport-replica-wishbone-set-a2-b2-s1-audi-quattro-sport.jpg?v=1765197583"},{"product_id":"subframe-bushings-b2b3b4","title":"Subframe bushings B2\/B3\/B4","description":"Get rid of your old rubber bushings and insert aluminium ones that will increase stability of the car in the corner. Aluminium subframe bushings will give your suspension possibility to hold desired geometry under the forces while the car is maneuvering on the road. Now the subframe will not shift and the car will fill much more firm holding desired camber, caster and other geometry setups.\u003cbr\u003e\n\u003cbr\u003e\nWhat's Included:\u003cbr\u003e\n- 8 pices of aluminium bushings (10 mm bolt) that work with one of the cars axles (front or rear). For whole car you need to order two sets.\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- CAD designed CNC cut 7075 aluminium\u003cbr\u003e\n- Anodized in silver\u003cbr\u003e\n- Completely replaces OEM bushings to eliminate unwanted suspension movement\u003cbr\u003e\n- More precise feel and quicker reactions to steering input\u003cbr\u003e\n- Will not compress, crack or separate like rubber bushings\u003cbr\u003e\n- Created to reduce unwanted suspension flex","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826674913629,"sku":"SBK-001","price":99.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/sbk-001-11-aluminium-subframe-bushings-b2-b3-b4-audi-80-s2-coupe.jpg?v=1765197584"},{"product_id":"subframe-bushings-late-b4-front","title":"Subframe bushings late B4 front","description":"Get rid of your old rubber bushings and insert aluminium ones that will increase stability of the car in the corner. Aluminium subframe bushings will give your suspension possibility to hold desired geometry under the forces while the car is maneuvering on the road. Now the subframe will not shift and the car will fill much more firm holding desired camber, caster and other geometry setups.\u003cbr\u003e\n\u003cbr\u003e\nThe bushings enable 10 mm subframe movement that will enable more caster and wider wheel spacing in the car for improved stability.\u003cbr\u003e\n\u003cbr\u003e\nWhat's Included:\u003cbr\u003e\n- 8 pices of aluminium bushings (12 mm bolt hole) that work with one of the cars axles\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- CAD designed CNC cut 7075 aluminium\u003cbr\u003e\n- Anodized in silver\u003cbr\u003e\n- Completely replaces OEM bushings to eliminate unwanted suspension movement\u003cbr\u003e\n- More precise feel and quicker reactions to steering input\u003cbr\u003e\n- Will not compress, crack or separate like rubber bushings\u003cbr\u003e\n- Created to reduce unwanted suspension flex","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826674946397,"sku":"SBK-003","price":99.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/sbk-003-12-aluminium-subframe-bushings-b2-b3-b4-audi-80-s2-coupe.jpg?v=1765197586"},{"product_id":"subframe-bushings-b2b3b4-offset","title":"Subframe bushings B2\/B3\/B4 offset","description":"Get rid of your old rubber bushings and insert aluminium ones that will increase stability of the car in the corner. Aluminium subframe bushings will give your suspension possibility to hold desired geometry under the forces while the car is maneuvering on the road. Now the subframe will not shift and the car will fill much more firm holding desired camber, caster and other geometry setups.\u003cbr\u003e\n\u003cbr\u003e\nWhat's Included:\u003cbr\u003e\n- 8 pices of aluminium (10 mm bolt hole) bushings that work with one of the cars axles (front or rear). For both axles you need to order two sets.\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- CAD designed CNC cut 7075 aluminium\u003cbr\u003e\n- Anodized in silver\u003cbr\u003e\n- Completely replaces OEM bushings to eliminate unwanted suspension movement\u003cbr\u003e\n- More precise feel and quicker reactions to steering input\u003cbr\u003e\n- Will not compress, crack or separate like rubber bushings\u003cbr\u003e\n- Created to reduce unwanted suspension flex","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826674979165,"sku":"SBK-002","price":99.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/sbk-002-11-aluminium-subframe-bushings-b2-b3-b4-audi-80-s2-coupe.jpg?v=1765197587"},{"product_id":"polyurethane-bushes-37mm-audi-b2b3b4-track-hardness","title":"Polyurethane bushes 37mm - Audi B2\/B3\/B4 - track hardness","description":"Set for one axle (both left and right hand sides included) of polyurethane bushings. For front and rear you need to sets.\u003cbr\u003e\n\u003cbr\u003e\nPolyurethane bushings work ideally in performance suspensions. Rubber suspension bushings are a proven compromise in performance vehicles. When additional horsepower is added, plus size tires then OEM or rubber bushings tend to stress beyond design limits. Polyurethane bushings are strong enough to control movement and maintain wheel alignment. This is a set for one axle. Recommended to use with our AudiSport replica wishbones. OEM part nr 8A0407181\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eThis is a set one axle of polyurethane bushings. For front and rear you need to order two sets.\u003c\/strong\u003e\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eWhat's Included:\u003c\/b\u003e\u003cbr\u003e\n- four black Polyurethane bushings\u003cbr\u003e\n- four centering sleeves for the Polyurethane bushings\u003cbr\u003e\n- four metal washers\u003cbr\u003e\n- four teflon washers\u003cbr\u003e\n- grease for fittings the bushings in the wishbone\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eFeatures:\u003c\/b\u003e\u003cbr\u003e\n- polyurethane bushings size 37 mm\u003cbr\u003e\n- track stiffness rated 85 ShA\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eFitment:\u003c\/b\u003e\u003cbr\u003e\n-  37mm Pressed Front Arms - Audi B2\/B3\/B4 (not for cast iron arms)\u003cbr\u003e\n-  37mm Pressed Rear Arms - Audi B2 Sedan\/Coupe\u003cbr\u003e\n-  37mm Pressed Rear Arms - Audi B3 Sedan\/Coupe\u003cbr\u003e\n-  37mm Pressed Rear Arms - Audi B4 Coupe\u003cbr\u003e\n\u003cbr\u003e\nOEM part nr 8A0 407 181","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826675470685,"sku":"POW-001-85","price":108.57,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-001-85-polyurethane-bushes-audi-quattro-s2-b2-b3-b4-37-mm-1.jpg?v=1765197588"},{"product_id":"rear-track-rods-for-support-frame-with-arb","title":"Rear track rods for support frame with ARB","description":"Rear tie rod set for Audi Quattro (B2\/B3\/B4) made of 25 mm thick tube - same size as used in the B Group cars. Equipped with motorsport joints, spacers and locknuts. It enables very precise setting of rear geometry settings.\u003cbr\u003e\n\u003cbr\u003e\nThis track rod is for cars equipped with rear anti-roll bar in the rear subframe.\u003cbr\u003e\n\u003cbr\u003e\nIt’s a must have for track or race use, as the OEM ones give up in extreme conditions changing your geometry setup, while the car is in the corner.\u003cbr\u003e\n\u003cbr\u003e\nAll non-OEM parts necessary for the installation are supplied in the kit.\u003cbr\u003e\n\u003cbr\u003e\nTotal rod adjustment lengths (distances between the central axes of the uniballs):\u003cbr\u003e\nmin: 345 [\u003cspan class=\"il\"\u003emm\u003c\/span\u003e]\u003cbr\u003e\nmax: \u003cspan class=\"il\"\u003e377\u003c\/span\u003e[\u003cspan class=\"il\"\u003emm\u003c\/span\u003e]\u003cbr\u003e\n\u003cdiv\u003e\n\u003cbr\u003e\n\u003cdiv class=\"adm\"\u003e\n\u003cbr\u003e\n\u003cdiv id=\"q_10062\" class=\"ajR h4\"\u003e\u003c\/div\u003e\n\u003cbr\u003e\n\u003c\/div\u003e\n\u003cbr\u003e\n\u003c\/div\u003e\u003cbr\u003e\nWhat's included:\u003cbr\u003e\n- One set (two pieces) of rear black tire rods for rear with inox finish\u003cbr\u003e\n- Four motorsport tie rod ends (left and right threads)\u003cbr\u003e\n- Steel machined tie rod end adapters to fit stock bearing carriers\u003cbr\u003e\n- Self-locking nuts\u003cbr\u003e\n- Four rubber sealing boots\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- Works with stock or Audi Sport wishbones and OEM rear support frame with sway bar\u003cbr\u003e\n- 25 mm thick rear tire rods powder painted in black\u003cbr\u003e\n- Locknuts for securing the motorsport joints\u003cbr\u003e\n- Galvanized tire rod end adapters for fitting bearing carriers\u003cbr\u003e\n\u003cbr\u003e\nFits:\u003cbr\u003e\n- Audi B2 Coupe\/Sedan Quattro with rear ARB\u003cbr\u003e\n- Audi B3 Coupe\/Sedan Quattro with rear ARB\u003cbr\u003e\n- Audi B4 Coupe Quattro with rear ARB\u003cbr\u003e\n- Audi S2 Coupe","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826675634525,"sku":"TRS-002","price":281.6,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/trs-002-1-rear-track-rods-with-arb-audi-s2-b4.jpg?v=1765197592"},{"product_id":"rear-track-rods-for-support-frame-without-arb","title":"Rear track rods for support frame without ARB","description":"Rear tie rod set for Audi Quattro (B2\/B3\/B4) made of 25 mm thick tube - same size as used in the B Group cars. Equipped with motorsport joints, spacers and locknuts. It enables very precise setting of rear geometry settings.\u003cbr\u003e\n\u003cbr\u003e\nThis track rod is for cars without rear anti-roll bar (ARB) in the rear subframe.\u003cbr\u003e\n\u003cbr\u003e\nIt’s a must have for track or race use, as the OEM ones give up in extreme conditions changing your geometry setup, while the car is in the corner.\u003cbr\u003e\n\u003cbr\u003e\nAll non-OEM parts necessary for the installation are supplied in the kit.\u003cbr\u003e\n\u003cbr\u003e\nTotal rods adjustment lengths (distances between the central axes of the uniballs)::\u003cbr\u003e\nmin: 293 [mm]\u003cbr\u003e\nmax: 325 [mm]\u003cbr\u003e\n\u003cbr\u003e\nWhat's included:\u003cbr\u003e\n- One set (two pieces) of rear black tire rods for rear with inox finish\u003cbr\u003e\n- Four motorsport racing tie rod ends (left and right threads)\u003cbr\u003e\n- Steel machined tie rod end adapters to fit stock bearing carriers\u003cbr\u003e\n- Self-locking nuts\u003cbr\u003e\n- Four rubber sealing boots\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- Works with stock or Audi Sport wishbones and OEM rear support frame with sway bar\u003cbr\u003e\n- 25 mm thick rear tire rods powder painted in black\u003cbr\u003e\n- Locknuts for securing the motorsport joints\u003cbr\u003e\n- Galvanized tire rod end adapters for fitting bearing carriers\u003cbr\u003e\n\u003cbr\u003e\nFits:\u003cbr\u003e\n- Audi B2 Coupe\/Sedan Quattro without rear ARB with newer type divided wheel knuckle.\u003cbr\u003e\n- Audi B3 Coupe\/Sedan Quattro without rear ARB with newer type divided wheel knuckle.\u003cbr\u003e\n- Audi B4 Coupe Quattro without rear ARB with newer type divided wheel knuckle.","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826676093277,"sku":"TRS-003","price":281.6,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/trs-003-1-rear-track-rods-for-support-frame-no-arb-audi-s2-b4.jpg?v=1765197593"},{"product_id":"front-track-rods-for-audi-b2b3b4","title":"Front track rods for Audi B2\/B3\/B4","description":"Steering rod set for Audi (B2, B3, B4) Coupe, Quattro, 80\/90\/Coupe, S2\/RS2, etc. 25 mm think tubing like in B Group times to provide strong and precision car handing in the corners under extreme loads.\u003cbr\u003e\n\u003cbr\u003e\nRods can be adjusted to fit any suspension settings including longer Audi Sport wishbones.\u003cbr\u003e\n\u003cbr\u003e\nMotorsport tie rod ends will withhold any stress while the car is on the track or bumpy gravel road. Locknuts on every end of the stick will enable precision alignment of the suspension.\u003cbr\u003e\n\u003cbr\u003e\nAll non-OEM parts necessary for the installation are supplied in the kit.\u003cbr\u003e\n\u003cbr\u003e\nWhat's Included:\u003cbr\u003e\n- One set (two pieces) of front track rods with inox finish\u003cbr\u003e\n- Four motorsport tie rod ends\u003cbr\u003e\n- Steel machined tie rod end adapters to fit to stock uprights (B3\/B4 type)\u003cbr\u003e\n- Self-locking nuts\u003cbr\u003e\n- Four rubber sealing boots\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- Works with stock OEM or Audi Sport wishbones\u003cbr\u003e\n- 25 mm thick steering rods powder painted in black\u003cbr\u003e\n- Locknuts for securing the motorsport joints\u003cbr\u003e\n- Galvanized tire rod end adapters for fitting bearing carriers\u003cbr\u003e\n\u003cbr\u003e\nFits (does not fit cars with 10VT engines) :\u003cbr\u003e\n- Audi 80 B2 (FWD \u0026amp; Quattro)\u003cbr\u003e\n- Audi 80\/90 B3 (FWD \u0026amp; Quattro)\u003cbr\u003e\n- Audi 80\/90 B4 (FWD \u0026amp; Quattro)\u003cbr\u003e\n- Audi S2\u003cbr\u003e\n- Audi RS2\u003cbr\u003e\n- Audi Ur-Quattro with B3\/B4 uprights\u003cbr\u003e\n- Audi Coupe Quattro\u003cbr\u003e\n- Audi Ur Quattro 20vt (please notice this in the comment when making order).\u003cbr\u003e\n\u003cbr\u003e\nIt will not fit:\u003cbr\u003e\n- Audi Ur-Quattro 10vt\u003cbr\u003e\n\u003cbr\u003e\n\u003cem\u003eNotice: Some clearancing of the steering rack bracket may be necessary to prevent binding or interference, depending on your suspension settings. Usually not needed unless you have large caster setup.\u003c\/em\u003e","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826676126045,"sku":"TRS-001","price":292.6,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/trs-001-1-front-track-rods-steering-rod-for-audi-s2-b4.jpg?v=1765197594"},{"product_id":"audi-quattro-rear-differential-mount-audi-b3b4-coupe-track-hardness","title":"Audi Quattro rear differential mount - Audi B3\/B4 coupe - track hardness","description":"Audi Quattro rear differential polyurethane mount.\u003cbr\u003e\n\u003cbr\u003e\nUnlike other products on the market this one fits perfectly on the both sides of the aluminium casting and on to for subframe metal mount. Our product is precisely undercut to fit the rear diff gearbox support. Other products have the same width of the outer edge and this makes it bad fit for the subframe mount.\u003cbr\u003e\n\u003cbr\u003e\nPolyurethane bushings work ideally in performance suspensions. Rubber suspension bushings are a proven compromise in performance vehicles. When additional horsepower is added, plus size tires then OEM or rubber bushings tend to stress beyond design limits. Polyurethane bushings are strong enough to control movement and maintain wheel alignment.\u003cbr\u003e\n\u003cbr\u003e\nOEM part is N\/A but it was used in rear gearbox support part number 895599125\u003cbr\u003e\n\u003cbr\u003e\nIt can be also used with Audi Sport Quattro replica mounting (upside down) to the car body.\u003cbr\u003e\n\u003cbr\u003e\nWhat’s Included:\u003cbr\u003e\n– Black polyurethane bushing for rear gearbox support  (aluminium arm not included)\u003cbr\u003e\n– grease for fittings the bushing\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n– track stiffness rated 85 ShA\u003cbr\u003e\n\u003cbr\u003e\nFitment:\u003cbr\u003e\n– Audi B2 Coupe Quattro\u003cbr\u003e\n- Audi Ur-Quattro\u003cbr\u003e\n– Audi B3 Coupe Quattro\u003cbr\u003e\n– Audi B4 Coupe Quattro\u003cbr\u003e\n- Audi S2 Coupe\u003cbr\u003e\n\u003cbr\u003e\nNotice: Audi made rear diff mount housing in two sizes, our mount is made to fit for the larger housing, smaller housing will is 0.5mm in diameter smaller and you will need to shim it with a sanding drum or roll.","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826679501149,"sku":"POW-012-85","price":45.04,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-012-85-audi-quattro-rear-differential-mount-s2-b4-80-90-1.jpg?v=1765197612"},{"product_id":"front-arb-26-mm-polyurethane-bushes-audi-b4-track-hardness","title":"Front ARB 26 mm polyurethane bushes - Audi B4 - track hardness","description":"Set for one front anti-roll bar of polyurethane bushings.\u003cbr\u003e\n\u003cbr\u003e\nPolyurethane bushings work ideally in performance suspensions. Rubber suspension bushings are a proven compromise in performance vehicles. When additional horsepower is added, plus size tires then OEM or rubber bushings tend to stress beyond design limits. Polyurethane bushings are strong enough to control movement and maintain wheel alignment. OEM part nr 811411327B\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eWhat's Included:\u003c\/b\u003e\u003cbr\u003e\n- two black polyurethane bushings\u003cbr\u003e\n- grease for fittings the bushings in to anti-roll bar\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eFeatures:\u003c\/b\u003e\u003cbr\u003e\n- polyurethane bushings size 26 mm\u003cbr\u003e\n- stiffness rated 85 ShA\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eFitment:\u003c\/b\u003e\u003cbr\u003e\n- 26mm front ARB - Audi B2\/B3\/B4\u003cbr\u003e\n\u003cbr\u003e\nOEM part nr 811 411 327 B","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826680320349,"sku":"POW-019-85","price":40.43,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-019-85-front-arb-26-mm-polyurethane-bushes-audi-s2-1.jpg?v=1765197618"},{"product_id":"polyurethane-subframe-bushings-b2b3b4-m10-track-hardness-black","title":"Polyurethane subframe bushings B2\/B3\/B4 - M10 - track hardness black","description":"Set for one subrame of Polyurethane Subframe Bushings - size M10.\u003cbr\u003e\n\u003cbr\u003e\nPolyurethane bushings work ideally in performance suspensions. Rubber suspension bushings are a proven compromise in performance vehicles. When additional horsepower is added, plus size tires then OEM or rubber bushings tend to stress beyond design limits. Polyurethane bushings are strong enough to control movement and maintain wheel alignment.\u003cbr\u003e\n\u003cbr\u003e\nThey can be used to maintain the stock suspension comfort.\u003cbr\u003e\n\u003cbr\u003e\nWhat's Included:\u003cbr\u003e\n- 4 pices of \u003cstrong\u003eblack\u003c\/strong\u003e polyurethane bushings (10 mm bolt) that work with one of the cars axles\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- Completely replaces OEM bushings to eliminate unwanted suspension movement\u003cbr\u003e\n- More precise feel and quicker reactions to steering input\u003cbr\u003e\n- Created to reduce unwanted suspension flex\u003cbr\u003e\n- Track hardness rated 85 ShA\u003cbr\u003e\n\u003cbr\u003e\nFitment:\u003cbr\u003e\n- Audi B2\u003cbr\u003e\n- Audi B3\u003cbr\u003e\n- Audi B4 with M10 bolt","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826681008477,"sku":"POW-018-85","price":102.79,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-018-85-polyurethane-subframe-bushings-b2-b3-b4-90-80-audi-s2-rs2-1.jpg?v=1765197622"},{"product_id":"polyurethane-bushes-37mm-audi-b2b3b4-street-hardness","title":"Polyurethane bushes 37mm - Audi B2\/B3\/B4 - street hardness","description":"Set for one axle (both left and right hand sides included) of polyurethane bushings. For front and rear you need to sets.\u003cbr\u003e\n\u003cbr\u003e\nPolyurethane bushings work ideally in performance suspensions. Rubber suspension bushings are a proven compromise in performance vehicles. When additional horsepower is added, plus size tires then OEM or rubber bushings tend to stress beyond design limits. Polyurethane bushings are strong enough to control movement and maintain wheel alignment. This is a set for one axle. Recommended to use with our AudiSport replica wishbones. OEM part nr 8A0407181\u003cbr\u003e\n\u003cbr\u003e\n\u003cstrong\u003eThis is a set one axle of polyurethane bushings. For front and rear you need to order two sets.\u003c\/strong\u003e\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eWhat's Included:\u003c\/b\u003e\u003cbr\u003e\n- four red Polyurethane bushings\u003cbr\u003e\n- four centering sleeves for the Polyurethane bushings\u003cbr\u003e\n- four metal washers\u003cbr\u003e\n- four teflon washers\u003cbr\u003e\n- grease for fittings the bushings in the wishbone\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eFeatures:\u003c\/b\u003e\u003cbr\u003e\n- polyurethane bushings size 37 mm\u003cbr\u003e\n- street stiffness rated 75 ShA\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eFitment:\u003c\/b\u003e\u003cbr\u003e\n-  37mm Pressed Front Arms - Audi B2\/B3\/B4 (not for cast iron arms)\u003cbr\u003e\n-  37mm Pressed Rear Arms - Audi B2 Sedan\/Coupe\u003cbr\u003e\n-  37mm Pressed Rear Arms - Audi B3 Sedan\/Coupe\u003cbr\u003e\n-  37mm Pressed Rear Arms - Audi B4 Coupe\u003cbr\u003e\n\u003cbr\u003e\nOEM part nr 8A0 407 181","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826689560925,"sku":"POW-001-75","price":108.57,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-001-75-polyurethane-bushes-37mm-audi-b2-b3-b4-street-s2-ur-quattro-80-90-1.jpg?v=1765197659"},{"product_id":"front-arb-26-mm-polyurethane-bushes-audi-b4-steet-hardness","title":"Front ARB 26 mm polyurethane bushes - Audi B4 - steet hardness","description":"Set for one front anti-roll bar of polyurethane bushings.\u003cbr\u003e\n\u003cbr\u003e\nPolyurethane bushings work ideally in performance suspensions. Rubber suspension bushings are a proven compromise in performance vehicles. When additional horsepower is added, plus size tires then OEM or rubber bushings tend to stress beyond design limits. Polyurethane bushings are strong enough to control movement and maintain wheel alignment. OEM part nr 811411327B\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eWhat's Included:\u003c\/b\u003e\u003cbr\u003e\n- two red polyurethane bushings\u003cbr\u003e\n- grease for fittings the bushings in to anti-roll bar\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eFeatures:\u003c\/b\u003e\u003cbr\u003e\n- polyurethane bushings size 26 mm\u003cbr\u003e\n- street stiffness rated 75 ShA\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eFitment:\u003c\/b\u003e\u003cbr\u003e\n- 26mm front ARB - Audi B2\/B3\/B4\u003cbr\u003e\n\u003cbr\u003e\nOEM part nr 811 411 327 B","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826691133789,"sku":"POW-019-75","price":40.43,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-019-75-front-arb-26-mm-polyurethane-bushes-audi-b4-s2-red-80-90-2.jpg?v=1765197666"},{"product_id":"front-anti-roll-bar-bush-28mm-audi-rs2-street-hardness","title":"Front anti roll bar bush 28mm - Audi RS2 - street hardness","description":"Set for one front anti-roll bar of polyurethane bushings.\u003cbr\u003e\n\u003cbr\u003e\nPolyurethane bushings work ideally in performance suspensions. Rubber suspension bushings are a proven compromise in performance vehicles. When additional horsepower is added, plus size tires then OEM or rubber bushings tend to stress beyond design limits. Polyurethane bushings are strong enough to control movement and maintain wheel alignment. OEM part nr 8A0411327\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eWhat's Included:\u003c\/b\u003e\u003cbr\u003e\n- two red polyurethane bushings\u003cbr\u003e\n- grease for fittings the bushings in to anti-roll bar\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eFeatures:\u003c\/b\u003e\u003cbr\u003e\n- polyurethane bushings size 28 mm\u003cbr\u003e\n- street stiffness rated 75 ShA\u003cbr\u003e\n\u003cbr\u003e\n\u003cb\u003eFitment:\u003c\/b\u003e\u003cbr\u003e\n- 28mm front ARB - Audi B2\/B3\/B4\u003cbr\u003e\n- Audi RS2\u003cbr\u003e\n\u003cbr\u003e\nOEM part nr 8A0 411 327","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826692149597,"sku":"POW-020-75","price":40.43,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-020-75-front-anti-roll-bar-bush-28mm-rs2-1.jpg?v=1765197673"},{"product_id":"polyurethane-subframe-bushings-b2b3b4-m10-steet-hardness","title":"Polyurethane subframe bushings B2\/B3\/B4 - M10 - steet hardness","description":"Set for one subrame of Polyurethane Subframe Bushings - size M10.\u003cbr\u003e\n\u003cbr\u003e\nPolyurethane bushings work ideally in performance suspensions. Rubber suspension bushings are a proven compromise in performance vehicles. When additional horsepower is added, plus size tires then OEM or rubber bushings tend to stress beyond design limits. Polyurethane bushings are strong enough to control movement and maintain wheel alignment.\u003cbr\u003e\n\u003cbr\u003e\nThey can be used to maintain the stock suspension comfort.\u003cbr\u003e\n\u003cbr\u003e\nWhat's Included:\u003cbr\u003e\n- 4 pices of red polyurethane bushings (10 mm bolt) that work with one of the cars axles\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- Completely replaces OEM bushings to eliminate unwanted suspension movement\u003cbr\u003e\n- More precise feel and quicker reactions to steering input\u003cbr\u003e\n- Created to reduce unwanted suspension flex\u003cbr\u003e\n- Street Hardness rated 75 ShA\u003cbr\u003e\n\u003cbr\u003e\nFitment:\u003cbr\u003e\n- Audi B2\u003cbr\u003e\n- Audi B3\u003cbr\u003e\n- Audi B4 with M10 bolt","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826693165405,"sku":"POW-018-75","price":102.79,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-018-75-polyurethane-subframe-bushings-b2-b3-b4-m10-steet-hardness-audi-quattro-s2-80-90-1.jpg?v=1765197678"},{"product_id":"differential-mounts-for-audi-quattro-b3b4-street-hardness","title":"Differential mounts for Audi Quattro B3\/B4 (street hardness)","description":"Differential mounts for Audi S2 Coupe and Audi B3 \/ B4 Coupe Quattro cars.\u003cbr\u003e\n\u003cbr\u003e\nUnlike in diff mounts manufactured by other companies our mounts have aluminium parts exposed from each other what makes the vibrations do not go out into the chassis dampening the vibrations in all directions.\u003cbr\u003e\n\u003cbr\u003e\nAlso we include aluminium spacer so the rear differential can be mounted horizontally. Other companies that sell the sets with out the spacer make the diff install crooked.\u003cbr\u003e\n\u003cbr\u003e\nWhat's included (kit for one car):\u003cbr\u003e\n- two gearbox mounts (left right)\u003cbr\u003e\n- aluminium spacer for left mount\u003cbr\u003e\n- set of screws\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- 7075 aluminium anodized silver\u003cbr\u003e\n- red street hardness 75 ShA polyurethane\u003cbr\u003e\n- set of 10.9 grade screws silver galvanized\u003cbr\u003e\n\u003cbr\u003e\nFits cars:\u003cbr\u003e\n- Audi S2 Coupe\u003cbr\u003e\n- Audi B3 (80,90) Quattro\u003cbr\u003e\n- Audi B4 (80,90) Quattro\u003cbr\u003e\n\u003cbr\u003e\nIt is an upgrade to OEM 8A0399151D and 431399151D","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826693755229,"sku":"ELA-003-75","price":179.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/diff-differential-mounts-for-audi-s2-b2-b4-coupe-quattro-ela-003-75-1.jpg?v=1765197683"},{"product_id":"engine-mounts-for-audi-5-cylinder-street-hardness","title":"Engine mounts for Audi 5-cylinder - street hardness","description":"Engine mounts for Audi S2\/RS2 and other 5-cylinder 20V turbo engines Audi 81 85 89 B3 B4 80 90 20V Turbo Coupe quattro.\u003cbr\u003e\n\u003cbr\u003e\nUnlike in mounts manufactured by other companies our mounts have aluminium parts are insulated from each other what makes the vibrations do not go out into the chassis dampening the vibrations in all directions.\u003cbr\u003e\n\u003cbr\u003e\nWhat's included (kit for one car):\u003cbr\u003e\n- two engine mounts (left and right)\u003cbr\u003e\n- set of screws\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- 7075 aluminium anodized silver\u003cbr\u003e\n- Red 75 ShA polyurethane\u003cbr\u003e\n- set of 10.9 grade screws silver galvanized\u003cbr\u003e\n\u003cbr\u003e\nFits cars:\u003cbr\u003e\n- Audi S2\u003cbr\u003e\n- Audi RS2\u003cbr\u003e\n- Audi C4 S4\/S6 with 5 cylinder engine\u003cbr\u003e\n- Audi B4 (80,90) with 5 cylinder engine\u003cbr\u003e\n- Audi UrQuattro\u003cbr\u003e\n- Audi B2 Coupe Quattro with 5 cylinder engine\u003cbr\u003e\n- Audi B4 Cabrio with 5 cylinder engine\u003cbr\u003e\n- Audi 200 20v\u003cbr\u003e\n\u003cbr\u003e\nIt is an upgrade to OEM 8A0399151D and 431399151D","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826694443357,"sku":"ELA-001-75","price":219.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/engine-mounts-for-audi-i5-s2-rs2-s4-200-20v-3b-aby-aan-adu-ela-001-2.jpg?v=1765197688"},{"product_id":"engine-mounts-for-audi-5-cylinder-track-hardness","title":"Engine mounts for Audi 5-cylinder - track hardness","description":"Engine mounts for Audi S2\/RS2 and other 5-cylinder 20V turbo engines Audi 81 85 89 B3 B4 80 90 20V Turbo Coupe quattro.\u003cbr\u003e\n\u003cbr\u003e\nUnlike in mounts manufactured by other companies our mounts have aluminium parts are insulated from each other what makes the vibrations do not go out into the chassis dampening the vibrations in all directions.\u003cbr\u003e\n\u003cbr\u003e\nWhat's included (kit for one car):\u003cbr\u003e\n- two engine mounts (left and right)\u003cbr\u003e\n- set of 10.9 screws\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- 7075 aluminium anodized silver\u003cbr\u003e\n- Black 85 ShA polyurethane\u003cbr\u003e\n- set of 10.9 grade screws silver galvanized\u003cbr\u003e\n\u003cbr\u003e\nFits cars:\u003cbr\u003e\n- Audi S2\u003cbr\u003e\n- Audi RS2\u003cbr\u003e\n- Audi C4 S4\/S6 with 5 cylinder engine\u003cbr\u003e\n- Audi B4 (80,90) with 5 cylinder engine\u003cbr\u003e\n- Audi UrQuattro\u003cbr\u003e\n- Audi B2 Coupe Quattro with 5 cylinder engine\u003cbr\u003e\n- Audi B4 Cabrio with 5 cylinder engine\u003cbr\u003e\n- Audi 200 20v\u003cbr\u003e\n\u003cbr\u003e\nIt is an upgrade to OEM 8A0399151D and 431399151D","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826694508893,"sku":"ELA-001-85","price":219.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/gearbox-mounts-for-audi-b2-b4-i5-s2-quattro-track-ela-001-1.jpg?v=1765197689"},{"product_id":"differential-mounts-for-audi-quattro-b3b4-track-hardness","title":"Differential mounts for Audi Quattro B3\/B4 (track hardness)","description":"Differential mounts for Audi S2 Coupe and Audi B3 \/ B4 Coupe Quattro cars.\u003cbr\u003e\n\u003cbr\u003e\nUnlike in diff mounts manufactured by other companies our mounts have aluminium parts exposed from each other what makes the vibrations do not go out into the chassis dampening the vibrations in all directions.\u003cbr\u003e\n\u003cbr\u003e\nAlso we include aluminium spacer so the rear differential can be mounted horizontally. Other companies that sell the sets with out the spacer make the diff install crooked.\u003cbr\u003e\n\u003cbr\u003e\nWhat's included (kit for one car):\u003cbr\u003e\n- two gearbox mounts (left right)\u003cbr\u003e\n- aluminium spacer for left mount\u003cbr\u003e\n- set of screws\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- 7075 aluminium anodized silver\u003cbr\u003e\n- black track hardness 85 ShA polyurethane\u003cbr\u003e\n- set of 10.9 grade screws silver galvanized\u003cbr\u003e\n\u003cbr\u003e\nFits cars:\u003cbr\u003e\n- Audi S2 Coupe\u003cbr\u003e\n- Audi B3 (80,90) Quattro\u003cbr\u003e\n- Audi B4 (80,90) Quattro\u003cbr\u003e\n\u003cbr\u003e\nIt is an upgrade to OEM 8A0399151D and 431399151D","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826695721309,"sku":"ELA-003-85","price":179.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/differential-mounts-for-audi-quattro-b3-b4-track-ela-003-1.jpg?v=1765197694"},{"product_id":"gearbox-mounts-for-audi-b4-i5-track-hardness","title":"Gearbox mounts for Audi B4 I5 (track hardness)","description":"Gearbox mounts for Audi S2\/RS2 and other 5-cylinder 20V turbo engines Audi 81 85 89 B3 B4 80 90 20V Turbo Coupe quattro.\u003cbr\u003e\n\u003cbr\u003e\nUnlike in mounts manufactured by other companies our mounts have aluminium parts are insulated from each other what makes the vibrations do not go out into the chassis dampening the vibrations in all directions.\u003cbr\u003e\n\u003cbr\u003e\nWhat's included (kit for one car):\u003cbr\u003e\n- two gearbox mounts (left right)\u003cbr\u003e\n- set of screws\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- 7075 aluminium anodized silver\u003cbr\u003e\n- black track hardness 85 ShA polyurethane\u003cbr\u003e\n- set of 10.9 grade screws silver galvanized\u003cbr\u003e\n\u003cbr\u003e\nFits cars:\u003cbr\u003e\n- Audi S2\u003cbr\u003e\n- Audi RS2\u003cbr\u003e\n- Audi B4 (80,90) with 5 cylinder engine\u003cbr\u003e\n- 100, 100 Avant with 5 cylinder engine\u003cbr\u003e\n- 200, 200 Avant with 5 cylinder engine\u003cbr\u003e\n- Audi B4 Cabrio with 5 cylinder engine\u003cbr\u003e\n\u003cbr\u003e\nIt is an upgrade to OEM 8A0399151D and 431399151D","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826701160797,"sku":"ELA-002-85","price":179.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/gearbox-mounts-for-audi-b4-i5-track-ela-002-1.jpg?v=1765197695"},{"product_id":"audi-quattro-rear-differential-mount-audi-b3b4-coupe-street-hardness","title":"Audi Quattro rear differential mount - Audi B3\/B4 coupe - street hardness","description":"Audi Quattro rear differential polyurethane mount.\u003cbr\u003e\n\u003cbr\u003e\nUnlike other products on the market this one fits perfectly on the both sides of the aluminium casting and on to for subframe metal mount. Our product is precisely undercut to fit the rear diff gearbox support. Other products have the same width of the outer edge and this makes it bad fit for the subframe mount.\u003cbr\u003e\n\u003cbr\u003e\nPolyurethane bushings work ideally in performance suspensions. Rubber suspension bushings are a proven compromise in performance vehicles. When additional horsepower is added, plus size tires then OEM or rubber bushings tend to stress beyond design limits. Polyurethane bushings are strong enough to control movement and maintain wheel alignment.\u003cbr\u003e\n\u003cbr\u003e\nOEM part is N\/A but it was used in rear gearbox support part number 895599125\u003cbr\u003e\n\u003cbr\u003e\nWhat’s Included:\u003cbr\u003e\n– Red polyurethane bushing for rear gearbox support (aluminium arm not included)\u003cbr\u003e\n– grease for fittings the bushing\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n– red street stiffness rated 75 ShA\u003cbr\u003e\n\u003cbr\u003e\nFitment:\u003cbr\u003e\n– Audi B2 Coupe Quattro\u003cbr\u003e\n- Audi Ur-Quattro\u003cbr\u003e\n– Audi B3 Coupe Quattro\u003cbr\u003e\n– Audi B4 Coupe Quattro\u003cbr\u003e\n- Audi S2 Coupe\u003cbr\u003e\n\u003cbr\u003e\nNotice: Audi made rear diff mount housing in two sizes, our mount is made to fit for the larger housing, smaller housing will is 0.5mm in diameter smaller and you will need to shim it with a sanding drum or roll.","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826703946077,"sku":"POW-012-75","price":45.04,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-012-75-audi-quattro-rear-differential-mount-audi-b3-b4-coupe-street-hardness-s2-80-90-quattro-2.jpg?v=1765197709"},{"product_id":"polyurethane-front-snub-engine-mount-audi-b2b3b4b5c4","title":"Polyurethane front snub engine mount - Audi B2\/B3\/B4\/B5\/C4","description":"Our polyurethane front snub engine mount is designed to reduce unwanted engine movement and is direct replacement of OEM unit.\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- reduces unwanted engine movement\u003cbr\u003e\n- stabilizes motor while car is accelerating\u003cbr\u003e\n- longer life\u003cbr\u003e\n\u003cbr\u003e\nWorks with Audi models up to (including) year 2001.\u003cbr\u003e\n- Audi B2 inc. Ur-Quattro\u003cbr\u003e\n- Audi B3\u003cbr\u003e\n- Audi B4 inc. S2 and RS2\u003cbr\u003e\n- Audi B5 inc. S4 2.7T\u003cbr\u003e\n- Audi C4 inc. S4 2.2T\u003cbr\u003e\n- Audi C5 A6 2.7T\u003cbr\u003e\n\u003cbr\u003e\nDoes not fit:\u003cbr\u003e\n- Audi V8\u003cbr\u003e\n- Audi C5 RS6\u003cbr\u003e\n- cars with 4.2 engine","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826710139229,"sku":"POW-082-75","price":30.45,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-082-75-polyurethane-snub-mount-audi-b2-b3-b4-b5-c4-s2-s4-rs2-c4-s4-s6-urs4-urs6-1.jpg?v=1765197725"},{"product_id":"audi-coupe-quattro-b2b3b4-rear-tubular-subframe","title":"Audi coupe Quattro B2\/B3\/B4 rear tubular subframe","description":"After long CAD development based on 3D scan of OEM subframes, tested with CAD FEA (Finite element method) and road going tests you can now buy brand new, rust free, subframes for your Audi Coupe Quattro. Using same T45 tubing as in WRC cars, our subframes provide increased stiffness and mass reduction. Additional mounting points for wishbones provide possibility for adjusting wishbones to get a horizontal position for the wishbone while the car is under load.\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- 9,5 kg, it is 3 kg saving over OEM subframes\u003cbr\u003e\n- T45 (BS4T45 to BS4T100) tubing imported from UK and S355 metal sheets\u003cbr\u003e\n- all components TIG welded\u003cbr\u003e\n- delivered painted (powder coated) black or on special order ( 50 euro) any RAL color\u003cbr\u003e\n- adjustable wishbone height (-20 mm or 20 mm over OEM) adjustment\u003cbr\u003e\n- solid mounts to the car body for increased stiffness and mass reduction\u003cbr\u003e\n- includes rear anti-roll bar mounts\u003cbr\u003e\n- additional reinforcement for track rods. OEM or aftermarket.\u003cbr\u003e\n- can be used with OEM wishbones or Audi Sport wishbones\u003cbr\u003e\n- OEM mounts to the car body and rear differential\u003cbr\u003e\n\u003cbr\u003e\nWhat is included:\u003cbr\u003e\n- rear subframe\u003cbr\u003e\n- rear anti-roll bar aluminum mounting inserts with bolts\u003cbr\u003e\n- bolts to screw subframe to car body\u003cbr\u003e\n- bolts for the wishbones\u003cbr\u003e\n\u003cbr\u003e\nCan be used in:\u003cbr\u003e\n- Audi B2 Coupe Quattro\u003cbr\u003e\n- Audi UrQuattro\u003cbr\u003e\n- Audi B3 Sedan\/Coupe Quattro\u003cbr\u003e\n- Audi B4 80\/90 Coupe Quattro\u003cbr\u003e\n- Audi S2 Coupe\u003cbr\u003e\n\u003cbr\u003e\nT45 (full name BS4T45 to BS4T100) is a very unique seamless carbon based steel tube that has been used in many applications in different industries. It is stronger than Co-Mo 4130 tubing that also used in motorsport. It is widely used in the aerospace sector in equipment such as pilot’s seats and crew’s seats due to the materials ability to withstand high G forces without snapping or splitting. This material is a Carbon Manganese based and conforms to the full Aerospace Specification laid down by British Standards.\u003cbr\u003e\n\u003cbr\u003e\nT45 Properties\u003cbr\u003e\nTensile: 700 – 900MPa,\u003cbr\u003e\n0.2% Yield 620MPa minimum\u003cbr\u003e\nHardness Test: 201min – 262 max HB or 210min – 275max HV.\u003cbr\u003e\n\u003cbr\u003e\n \u003cbr\u003e\n\u003cbr\u003e\nNotice: Sold for off road, track and racing applications only. We strongly advice to mount the subframe in qualified and experienced workshop that would know what they are doing.","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826711286109,"sku":"WAS-101","price":1299.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/75D_4824-1.jpg?v=1765197731"},{"product_id":"audi-quattro-b2b3b4-front-tubular-subframe","title":"Audi Quattro B2\/B3\/B4 front tubular subframe","description":"After long CAD development based on 3D scan of OEM subframes, tested with CAD FEA (Finite element method) and road going tests you can now buy brand new, rust free, subframes for your Audi Coupe Quattro. Using same T45 tubing as in WRC cars, our subframes provide increased stiffness and mass reduction. Additional mounting points for wishbones provide possibility for adjusting wishbones to get a horizontal position for the wishbone while the car is under load.\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- 7,2 kg, it is 5.5 kg saving over OEM subframe\u003cbr\u003e\n- T45 (BS4T45 ( A2) to BS5T100 \u0026amp; BS6 S100) tubing imported from UK and S355 metal sheets\u003cbr\u003e\n- all components TIG welded\u003cbr\u003e\n- delivered painted (powdercoated) black or on special order ( 50 euro) any RAL color\u003cbr\u003e\n- adjustable wishbone height (-20 mm or 20 mm over OEM) adjustment\u003cbr\u003e\n- solid mounts to the car body for increased stiffness and mass reduction\u003cbr\u003e\n- includes front anti-roll bar mounts\u003cbr\u003e\n- mounts for 6 gear gearbox (01E)\u003cbr\u003e\n- can be used with OEM wishbones or Audi Sport wishbones\u003cbr\u003e\n- mounts to the OEM car body\u003cbr\u003e\n\u003cbr\u003e\nWhat is included:\u003cbr\u003e\n- front subframe\u003cbr\u003e\n- front anti-roll bar aluminum mounting inserts with bolts\u003cbr\u003e\n- bolts to screw subframe to car body\u003cbr\u003e\n- bolts for the wishbones\u003cbr\u003e\n\u003cbr\u003e\nUsed in:\u003cbr\u003e\n- Audi B2 Sedan\/Coupe 5-cylinder\u003cbr\u003e\n- Audi UrQuattro\u003cbr\u003e\n- Audi B3 80\/90 Sedan\/Coupe 5-cylinder\u003cbr\u003e\n- Audi B4 80\/90 Sedan\/Coupe\/Avant 5-cylinder\u003cbr\u003e\n- Audi S2 Sedan\/Coupe\/Avant\u003cbr\u003e\n- Audi RS2\u003cbr\u003e\n\u003cbr\u003e\nT45 is a very unique seamless carbon based steel tube that has been used in many applications in different industries. It is stronger than Co-Mo 4130 tubing that also used in motorsport. It is widely used in the aerospace sector in equipment such as pilot’s seats and crew’s seats due to the materials ability to withstand high G forces without snapping or splitting. This material is a Carbon Manganese based and conforms to the full Aerospace Specification laid down by British Standards.\u003cbr\u003e\n\u003cbr\u003e\nProperties\u003cbr\u003e\nTensile: 700 – 900MPa,\u003cbr\u003e\n0.2% Yield 620MPa minimum\u003cbr\u003e\nHardness Test: 201min – 262 max HB or 210min – 275max HV.\u003cbr\u003e\n\u003cbr\u003e\n \u003cbr\u003e\n\u003cbr\u003e\nNotice: Sold for off road, track and racing applications only. We strongly advice to mount the subframe in qualified and experienced workshop that would know what they are doing.","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826711318877,"sku":"WAS-100","price":1099.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/75D_4831-1.jpg?v=1765197733"},{"product_id":"audi-coupe-quattro-b2b3b4-front-and-rear-tubular-subframes","title":"Audi coupe Quattro B2\/B3\/B4 front and rear tubular subframes","description":"After long CAD development based on 3D scan of OEM subframes, tested with CAD FEA (Finite element method) and road going tests you can now buy brand new, rust free, subframes for your Audi Coupe Quattro. Using same T45 tubing as in WRC cars, our subframes provide increased stiffness and mass reduction. Additional mounting points for wishbones provide possibility for adjusting wishbones to get a horizontal position for the wishbone while the car is under load.\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- 7,2 kg, it is 5.5 kg saving over OEM subframe front\u003cbr\u003e\n- 9,5 kg, it is 3.5 kg saving over OEM subframe rear\u003cbr\u003e\n- T45 (BS4T45 (+A2) to BS5T100 \u0026amp; BS6 S100) tubing imported from UK and S355 metal sheets\u003cbr\u003e\n- all components TIG welded\u003cbr\u003e\n- delivered painted (powdercoated) black or on special order (+50 euro) any RAL color\u003cbr\u003e\n- adjustable wishbone height (-20 mm or + 20 mm over OEM) adjustment\u003cbr\u003e\n- solid mounts to the car body for increased stiffness and mass reduction\u003cbr\u003e\n- includes front and rear anti-roll bar mounts\u003cbr\u003e\n- front subframe for 6 gear garbox (01E) mounts\u003cbr\u003e\n- additional reinforcement for rear track rods. OEM or aftermarket.\u003cbr\u003e\n- can be used with OEM wishbones or Audi Sport wishbones\u003cbr\u003e\n- mounts to OEM the car body\u003cbr\u003e\n\u003cbr\u003e\nWhat is included:\u003cbr\u003e\n- front subframe\u003cbr\u003e\n- rear subframe\u003cbr\u003e\n- front and rear anti-roll bar aluminum mounting inserts with bolts\u003cbr\u003e\n- bolts to screw subframe to car body\u003cbr\u003e\n- bolts for the wishbones\u003cbr\u003e\n\u003cbr\u003e\nUsed in:\u003cbr\u003e\n- Audi B2 Coupe Quattro 5-cylinder\u003cbr\u003e\n- Audi UrQuattro\u003cbr\u003e\n- Audi B3 80\/90 Sedan\/Coupe Quattro 5-cylinder\u003cbr\u003e\n- Audi B4 80\/90 Coupe Quattro 5-cylinder\u003cbr\u003e\n- Audi S2 Coupe\u003cbr\u003e\n\u003cbr\u003e\nT45 is a very unique seamless carbon based steel tube that has been used in many applications in different industries. It is stronger than Co-Mo 4130 tubing that also used in motorsport. It is widely used in the aerospace sector in equipment such as pilot’s seats and crew’s seats due to the materials ability to withstand high G forces without snapping or splitting. This material is a Carbon Manganese based and conforms to the full Aerospace Specification laid down by British Standards.\u003cbr\u003e\n\u003cbr\u003e\nProperties\u003cbr\u003e\nTensile: 700 – 900MPa,\u003cbr\u003e\n0.2% Yield 620MPa minimum\u003cbr\u003e\nHardness Test: 201min – 262 max HB or 210min – 275max HV.\u003cbr\u003e\n\u003cbr\u003e\nNotice: Sold for off road, track and racing applications only. We strongly advice to mount the subframe in qualified and experienced workshop that would know what they are doing.","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826711351645,"sku":"WAS-100-101","price":2278.1,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/audi-coupe-quattro-b2b3b4-typ-81-85-89-front-rear-tubular-subframe-was-100-101-1.jpg?v=1765197734"},{"product_id":"polyurethane-front-snub-engine-mount-black-audi-b2b3b4b5c4","title":"Polyurethane front snub engine mount black - Audi B2\/B3\/B4\/B5\/C4","description":"Our polyurethane black front snub engine mount is designed to reduce unwanted engine movement and is direct replacement of OEM unit.\u003cbr\u003e\n\u003cbr\u003e\nFeatures:\u003cbr\u003e\n- reduces unwanted engine movement\u003cbr\u003e\n- stabilizes motor while car is accelerating\u003cbr\u003e\n- longer life\u003cbr\u003e\n\u003cbr\u003e\nWhat you get:\u003cbr\u003e\n- one black polyurethane front snub engine mount\u003cbr\u003e\n\u003cbr\u003e\nWorks with Audi models up to (including) year 2001.\u003cbr\u003e\n- Audi B2 inc. Ur-Quattro\u003cbr\u003e\n- Audi B3\u003cbr\u003e\n- Audi B4 inc. S2 and RS2\u003cbr\u003e\n- Audi B5 inc. S4 2.7T\u003cbr\u003e\n- Audi C4 inc. S4 2.2T\u003cbr\u003e\n- Audi C5 A6 2.7T\u003cbr\u003e\n\u003cbr\u003e\nDoes not fit:\u003cbr\u003e\n- Audi V8\u003cbr\u003e\n- Audi C5 RS6\u003cbr\u003e\n- cars with 4.2 engine","brand":"Verkline","offers":[{"title":"Default Title","offer_id":62826711941469,"sku":"POW-082-85","price":30.45,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/files\/pow-082-85-polyurethane-front-snub-engine-mount-audi-b2-b3-b4-b5-c4-s2-rs2-s4-s6-urs4-urs6-80-90-quattro-1.jpg?v=1765197737"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1001\/3451\/9133\/collections\/00135b0433d164efd716cdf8045968df.jpg?v=1774671640","url":"https:\/\/verkline.com\/collections\/audi-coupe-quattro-b2.oembed","provider":"VERKLINE","version":"1.0","type":"link"}