Fully Adjustable Wishbone Kit – BMW F8x M2 / M3 / M4 – Track Package - Stage 1

Pre-order Status: Active

Launch Offer: First 10 orders get 40% OFF + Eligibility for Stage 2 Discount.

⚠️ ONLY 1 KIT LEFT !

Orders Ship Late January 2026

The Market’s Only Full-Chassis Solution

The only 20-piece system that replaces the entire suspension kinematic chain on both Front and Rear axles. While competitors offer partial solutions, Verkline provides a total overhaul—including all Control Arms, Tie Rods, Drop Links, and Inserts—to fully correct geometry, enable necessary adjustability and eliminate 100% of rubber compliance.

Safety Architecture

We engineered the only CNC-milled Caster Arm on the market to eliminate the risks of competitor straight-rod designs. Our unique geometry provides essential clearance to prevent tie-rod collisions and actively tilts the bearing housing to optimize articulation, ensuring zero binding even at extreme steering angles.

Total Transformation

Replaces the entire compliant rubber kinematic chain with motorsport spherical bearings to eliminate unwanted deflection. This unlocks the true mechanical grip of the M-chassis, providing instant steering response, precise feedback, and consistent geometry under heavy braking and cornering loads.

Advanced Simulation & Testing

Engineered using the same rigorous simulation protocols we apply for top-tier WRC teams. We digitally subjected every component to 28 extreme load scenarios—including violent curb strikes and combined G-forces—to ensure structural integrity that far exceeds OEM standards, a level of validation rarely seen in the aftermarket.

Competitor Average Kits

VERKLINE Stage 1 kit

Rear Tubular Subframe • Billet CNC Front Uprights

A: Safety, clearance, and correct geometry. While all other competitors use simple straight rods, we engineered a complex CNC-milled design for three critical reasons:

• Clearance: A straight rod creates a high risk of collision with the steering tie-rod during suspension travel. Our milled shape provides the necessary clearance naturally without compromising safety.
• Bearing Articulation: A straight arm forces the spherical bearing to sit in-line with the arm, often exceeding its operating angle. Our milled design allows us to tilt the bearing housing, optimizing the articulation range to prevent dangerous binding.
• Structural Integrity: Competitors often use long studs or spacers to adjust anti-dive (or simply to avoid collisions), which weakens the stud. We keep the stud length standard for maximum strength. Furthermore, increasing anti-dive on a lowered F8x hurts handling; we address this correctly via our Stage 2 Uprights geometry, rather than using a compromised arm design.

A: In the BMW F8X factory rear suspension design, camber and bump steer are intrinsically linked; changing one directly affects the other. At the stock ride height (~90mm), the chassis allows for a camber adjustment range of 0.75° to 2.35°, which maintains acceptable geometry. This is illustrated in the graph below, where the blue line represents the minimum camber (0.75°), orange shows the factory specification (1.5°), and grey indicates the maximum camber (2.35°).

However, lowering the vehicle significantly alters the angle of the suspension arms and the position of the roll centre. When running a performance setup—for example, a 60mm ride height combined with 2.5° of negative camber—the stock geometry cannot compensate, leading to excessive and unwanted bump steer.

The Verkline Solution With our Stage 1 Kit, you regain complete control over your suspension kinematics. By replacing the fixed factory components with our adjustable lower trailing arms, you can effectively decouple camber settings from bump steer characteristics. This allows you to:

• Precise Bump Steer Tuning: Configure the exact amount of bump steer required for your driving style, or virtually eliminate it entirely for predictable handling at the limit.
• Extended Adjustment Range: We have eliminated the limiting factory eccentric bolt in favour of a fully adjustable arm system. This significantly increases the toe adjustment range, allowing you to run aggressive camber settings necessary for track grip without compromising straight-line stability or tire wear.

We provide details instructions with the kit on how to setup your suspension kinematics.

A: Engineering pragmatism. The OEM BMW rear upper arm is an exceptionally high-quality forged component. Replacing it with a billet arm adds cost and weight without improving performance. The flaw is the rubber bushing. Our kit replaces these with spherical bearings, retaining the superior OEM arm design while eliminating compliance.

A: Yes. Lowering an F8x alters the tie-rod angle, introducing "Bump Steer." Our kit includes adjustable tie rod ends and control arms that allow for individual bump steer correction. The lower trailing arm length is adjustable, giving you full control to "zero out" the bump steer curve.

A: The difference is bearings and testing. Chinese rod ends often develop play quickly. We use EU-manufactured Getecno motorsport bearings with self-lubricating PTFE liners (used in Pagani). With reinforced PTFE anti-friction liners, forged body, out of 42CrMo4 heat treated steel, for maximum load capacity. The inner ring is out of 100Cr6 carbon steel, hardened, ground and chrome plated.